Universal Remote Control Universal Remote UR J2000TVE User Manual |
STEP3 Point the remote control toward
the TV and enter the three-digit
code from the code table. If
there is more than one code
number assigned to your TV
brand, try one code number at a
time until the TV turns off right
after you entered the number.
*Tip: Red light will blink twice.
Instructions
Operating Manual
for 2 in 1 Cable TV
Remote Control
This remote control is preprogrammed
to operate CABLE Box.
The [CATV] button sends out the TV
and CABLE power commands if you
press the [CATV] button.
To return to the original function, press
the [CH-] button in the STEP2 .
Please program it for your TV by
following the instructions shown below.
Batteries
UR-J2000TVE
B. Recalling the TV Three-digit code :
The remote control uses AAA batteries.
Please be sure to match the batteries
Searching Method
STEP1 Press [TV] and [MUTE]
buttons simultaneously until
the red light is on.
Press [CH +] button and hold until the
TV turns off. As soon as the TV turns
off, release [CH+] button.
+
-
with the ( ) and ( ) markings inside the
battery compartment during installation.
STEP2 Press [VOLUME -] button.
*Tip: You can confirm the power off and
The red light will blink a number of
times indicating the number of each
digit of the code. Each digit is
separated by one second interval of
red light being off.
*Tip: One blink, three blinks and 10
blinks, indicates the code
number 130.
on by pressing [MUTE] button.
STEP4 Press [TV] button to store the
three-digit code.
*Tip: Red light will blink twice.
Install two AAA alkaline
batteries as shown here
Three-digit code :
Set-up for your VOLUME control
The remote control is preprogrammed
to control VOLUME and MUTE functions
through your TV. To switch VOLUME
and MUTE functions to your Cable Box:
Helpful hints
Set-up for your Cable Box
Press arrow gently &
pull down to remove cover
The remote control is preprogrammed
to control your cable box. If it does
not work properly, please set-up the
right code by using the three-digit
code or searching method.
If you have a TV with a remote
control, we recommend that you plug
its power cord directly into a wall
outlet if available (your cable installer
may select an alternate setup)
Programming your remote control
STEP1 Press [CATV] and [MUTE]
buttons simultaneously until
red light is on.
Setup for your cable box
No setup is required. The remote control is
preprogrammed to operate your cable box.
STEP2 Press [VOLUME +] button.
STEP3 Press [CATV] button.
To return to the TV’s VOLUME, press
[TV] button.
Setup for your TV
Find your TV brand and its three-digit
code on the back of this manual. If the
TV brand is not listed, please use the
Searching Method in STEP3 .
*Tip: Red light will blink twice.
Operation
If red light does not blink when
you press keys the operation is
intermittent:
Make sure the batteries are
inserted correctly.
Replace old batteries with two new
AAA batteries. Please do not mix
old batteries with new ones.
Set-up for advanced functions
A. To turn on your TV and Cable at the
same time with CATV button:
STEP1 Press [CATV] and [0] buttons
simultaneously until the red
light is on.
STEP1 Turn on your TV manually.
*Tip : If you have RCA TV, don’t turn
on the TV.
Universal Remote Control, Inc.
STEP2 Press [TV] and [MUTE] buttons
simultaneously until the red
light is on.
OEE-0017E Rev 02(05/14/02)
STEP2 Press [CH +] button.
|
Tatung Computer Monitor DS42 AV User Manual
Texas Instruments TV Converter Box TLV1562 User Manual
Toastmaster Toaster bt120 User Manual
Toshiba Air Conditioner RAV SP180UT UL User Manual
Toshiba Projection Television 50HX81 User Manual
TP Link Network Router TL MR3020 User Manual
Troy Bilt Brush Cutter 41 AM079G063 User Manual
Turbosound Speaker LMS A6 User Manual
ViewSonic Computer Monitor VX2453MH LED User Manual
Vulcan Hart Electric Steamer C24EA3 208 240V BASIC User Manual