PHONECELL SX3i AMPS
FIXED WIRELESS TERMINAL
USER MANUAL
Total communications freedom at your
fingertips...voice/fax/data.
12/08/99
Part No. 56016602
Table of Contents
Introduction...............................................................................................2
Technical Support...................................................................................2
Getting Started
Unpacking the Phonecell SX3i...............................................................4
Pre-Installation Checklist........................................................................4
Installation Summary ...............................................................................5
Step 1. Choose an Antenna Location.....................................................6
How to Connect the Antenna .................................................................7
Step 2. Plug in Your Telephone...............................................................8
Connect Your Telephone ........................................................................8
Place a Call – Adjust Your FWT.............................................................8
Connecting Additional Phones & Equipment..........................................8
Step 3. NAM/Phone Number Setup....................................................9-11
Optional A-Key (Authentication Code) Setup .......................................11
Step 4. Optional Battery Installation ...............................................12-13
Step 5. Install Your Phonecell
Wall-Mount Installation .........................................................................14
Desktop/Tabletop Installation................................................................15
Phonecell SX3i Operation
How to Use the LED Status Indicator...................................................16
How to Place a Call..............................................................................16
How to Receive a Call..........................................................................16
How to End a Call ................................................................................16
The Hookflash Function .......................................................................16
Important Tones and Alerts...................................................................17
How to Adjust the Volume Level...........................................................17
Fax/Data Transmission.........................................................................17
Variable Dial Time (Auto SENDDelay) Option.....................................18
Special Cellular Services.................................................................18-19
Data After SEND (In-Call DTMF Signaling) Option ..............................19
Zero Dial Delay for Frequently Called Numbers ..................................19
Phonecell SX3i Troubleshooting...........................................................20
Safety Information.............................................................................21-23
AMPS Technician Programming
How to Enter the Programming Mode..................................................24
How to Set the Access Overload Class (ACCOLC) .........................25
How to Set the Access Method (EX) Option ....................................25
How to Set the Roam Option............................................................25
How to Set the Dial Tone After Remote On-Hook Option ................25
How to Set the Post-Receiver Off-Hook (ROH) Option....................26
How to Set the Pulse Dial Option.....................................................26
How to Initiate a Ring-Back Request................................................26
How to Restore the Factory Default Settings...................................26
How to Enable/Disable the Zero Dial Delay Option .........................26
PHONECELL SX3i AMPS
3
USER MANUAL 12/08/99
Getting Started...
Un-Packing Your Phonecell SX3i
Ë
Í
Ì
Ê
The Phonecell SX3i comes with the following:
Phonecell SX3i Fixed Wireless Terminal (FWT)
AC Power Cord
Ê
Ë
Ì
Í
Drill Mounting Template
Three Rubber Feet for Desktop/Tabletop Use*
(*Do not attach feet if wall-mounting the FWT.)
Carefully remove the unit from the shipping carton and check for evidence
of shipping damage. If damage is found, contact your Authorized
Telular Distributor or shipping agent immediately.
Pre-Installation Checklist
Before attempting Phonecell SX3i installation, make sure you have the
following components, tools and materials.
Components Needed
Qty. Description
Supplied Not Supplied
1
2
Antenna (Spike, Magnetic-Mount, or Yagi)
4
4
6-Volt, 4.5 AH Lead-Acid Batteries (Optional
for Battery Backup)
1
1
RJ-11 Modular Phone Cord (Length varies
according to your specific installation and
the number of phones you plan to connect)
4
4
RJ-11 Phone Line Splitter (if you plan to
connect more than one telephone device)
Tools & Materials Needed (for Wall-Mount Installation Only)
Qty. Description
Supplied Not Supplied
1
1
2
Drill & Drill Bit
4
4
4
Screwdriver
11/2-inch (3.75 cm) Mounting Screws
PHONECELL SX3i AMPS
4
USER MANUAL 12/08/99
Installation Summary
There are five steps to installing the Phonecell SX3i FWT properly.
These steps are summarized below and explained in detail in the
remainder of this manual.
Step 1. Choose an Antenna Location (pg. 6-7)
·
·
·
·
Choose a location.
Next, connect power to the FWT.
Then, connect the antenna (not supplied).
Check the cellular signal strength and
move the antenna until you achieve the
best signal possible.
Step 2. Plug In Your Phone (page 8)
·
Once the antenna is connected, hook up
a phone.
· Then, make a test call to check noise levels,
and adjust the antenna location accordingly.
· NOTE: If your Phonecell SX3i is not pre-pro-
grammed for NAM (Number Assignment Module)
information, you’ll need to perform the
NAM/Phone Number Setup in Step 3. Then, return
to this step (2).
· Plug in additional phones, Fax and/or Modem.
Step 3. NAM/Phone Number Setup (pg. 9-11)
· If your Phonecell was not pre-programmed for
NAM information, you need to perform the
NAM/Phone Number Setup procedure.
F
· Otherwise, continue to Step 4.
Step 4. Battery Installation (pg. 12-13)
· Follow these instructions to install optional bat-
teries (not included) for backup in the
event of AC power failure.
·
Otherwise, continue to Step 5.
Step 5. Wall or Desk Installation (pg. 14-15)
·
After you’ve selected a location and made all
the necessary connections and adjustments,
your Phonecell SX3i is ready for either
wall-mounting or desktop/tabletop use.
PHONECELL SX3i AMPS
5
USER MANUAL 12/08/99
Step 1. Choose an Antenna Location
Your Phonecell SX3 receives operating commands from the cel-
lular network and relies upon signal strength for proper opera-
tion. Therefore, finding an antenna location with good signal
strength is critical for call quality.
ANTENNA LOCATION TIPS:
·
Locate the antenna above ground and as close
to windows (or exterior walls) as possible – see
Fig. 1.
·
Try to install the antenna in an uninhabited area
(i.e. closets, attics, etc.) to ensure a minimum
separation of 16 inches (40 cm) between the
antenna and the inhabitants.
·
In low signal areas, the antenna should be
mounted on the building’s exterior – see Fig. 2.
· High-gain (“Yagi”) antennas must be directed
toward your service provider’s nearest cellular
tower.
· Spike antennas must be pointed upward.
· Keep antenna cable as short as possible – long
cable runs affect call quality.
Fig. 1 Optional spike antenna point-
ed upward and located near the win-
dow for optimum signal strength.
· Never splice antenna cable.
Coaxial Cable
Fig. 2 Optional high-gain antenna installed on the building’s exterior. Always
direct the antenna toward the nearest cell tower of your service provider.
PHONECELL SX3i AMPS
6
USER MANUAL 12/08/99
Antenna Location & Setup – Continued
How to Connect the Antenna:
Fig. 3
1) Connect the AC line cord from the
power port on the front of the FWT
to the AC power source – see
Figure 3.
OR if an external DC power source
is used, connect an optional DC
input cable to the DC Input port.
LED
Indicator
Power
Switch
DC Port
2) Turn on the FWT power using the
power switch. After approximately
10 seconds, the LED indicator on
the front of the FWT should turn
RED.
AC Port
AC Line
Cord
3) Connect an antenna to the TNC
antenna connector on top of the
FWT – see Figure 4.
l
l
AC Power
4) Move the antenna from one location
to another until you achieve the best
signal strength possible.
ANTENNA TIP:
Many things can obstruct the cellular
signal, and moving the antenna as little as
one meter (3 feet) can dramatically
Optional High-Gain
improve signal strength and call reception.
Test the cellular signal strength
by checking the LED indicator
on the front of your Phonecell:
Optional
Spike
Optional
Magnetic-
Mount
· Solid RED = No Service
· Solid YELLOW = Moderate
signal strength
· Solid GREEN = Good signal
strength.
TNC Antenna
Connector
5) When you’re getting a strong
(GREEN) signal, you’re ready
for the next step – connecting
a phone and making a call.
Fig. 4
WARNING!
Never operate your Phonecell
when any person is within 16
inches (40 cm) of the antenna.
!
Power
Switch
LED
Indicator
PHONECELL SX3i AMPS
7
USER MANUAL 12/08/99
Step 2. Plug In Your Telephone
Your Phonecell SX3 lets you connect up to 5 pieces of standard telephone equip-
ment into a cellular network. Follow the steps below for quick installation.
Connect Your Telephone:
1) Locate the modular (RJ-11) line port
on your phone and plug in one end of
a standard (RJ-11) phone cord.
2) Connect the other end of the cord
to the RJ-11 port on the front
of your Phonecell SX3i – see Fig. 5.
Fig. 5
To RJ-11 Port
Place a Call – Adjust Your FWT:
1) Pick up the phone receiver and listen
for dial tone.
2) If you hear dial tone, make a call.
Phone Cord
3) While you’re talking with the other
party, listen for static and echo. If you
hear either, move the antenna until
you find the spot where voice conver-
sation is strong, and static
( )
To Phone s
and echo are minimized.
To
Modem
NOTE: If you are unsuccessful in
dialing out, verify the following:
· The antenna location needs to be
adjusted – see Step 1, page 6-7.
· The NAM/Phone Number needs to
be set up – see Step 3, page 9-11.
· Your cellular phone number has not
been activated – contact your cel-
lular service provider.
Adding More Phones?
Plug in an RJ-11 line splitter (not sup-
plied) to connect additional phones to
your FWT – see Fig. 6. NOTE: you can
only make one phone call at a time.
Line
Splitter
RJ-11
Port
Additional Telephone Equipment:
Phone
Cords
If you plan to use a device other than a
telephone with your Phonecell SX3 (such
as a modem), make sure that device will
work with a normal wired telephone line.
Fig. 6 Optional RJ-11 Line Splitter
lets you connect additional phone
equipment to your Phonecell SX3i.
Fax Machines – Connect a fax machine
the same way it needs to be set up for
use on a regular wired telephone line.
IMPORTANT!
Make sure the wiring from the
telephone equipment to your
Phonecell SX3 is properly
protected from all transient
voltages, including lightning.
PBX/KSU Systems – PABX
installation should only be performed
by experienced telephone technicians.
!
PHONECELL SX3i AMPS
8
USER MANUAL 12/08/99
Step 3. NAM/Phone Number Setup
IMPORTANT!
If your Phonecell was NOT pre-programmed for NAM (Number
Assignment Module/Phone Number) information, follow the
steps below. Otherwise, continue to STEP 4, pages 12,13.
!
You can program the Phonecell SX3 with an ordinary tone-dial (DTMF) telephone,
which is sometimes referred to as a POTS (Plain Old Telephone Service) phone.
NOTE: this programming mode is not accessible while you're in a call.
Step #1 - Pick up the POTS handset and listen for a tone (either a steady dial
tone or a beeping no-service tone).
Step #2 - Enter the Master-Programming mode by pressing:
# * 0 * 1 2 3 4 4 3 2 1 #
F
The dial tone should change to a different, steady “Programming” tone
and the LED indicator on the front of your Phonecell should blink
alternately RED and GREEN to indicate that you’re now in the
programming mode. You now have two minutes to begin the
programming steps below.
Step #3 - Press:
#
* 1 * _ _ _ _ _ _ _ _ _ _ #
F
The spaces represent your 10-digit telephone number. (This is also
called a Mobile Identification Number, or MIN.) If you enter the number
incorrectly, you'll hear three short tones followed by the programming
tone; if correct, you'll hear the programming tone again.
Step #4 - Press:
#
* 5 * _ _ _ _ _ #
F
The spaces represent your 1- to 5-digit System Identifier (SID), which
ranges from 0 to 32,767. This information identifies your cellular serv-
ice provider. (For example, to set up 555, enter #*5*555#.) If you enter
the SID incorrectly, you'll hear three short tones followed by the pro-
gramming tone; if correct, you'll hear the programming tone again.
NOTE: depending upon whether you enter an odd SID or an even SID,
the Phonecell will automatically set the remaining NAM parameters to
AMPS standards – as shown in the table below.
AMPS Standards
Automatically Set NAM Parameters
Initial Dedicated Control Channel
First Paging Channel
Odd SID
333
Even SID
334
333
334
Number of Dedicated Control Channels
Preferred System
21
A
21
B
Roam Option (to override, see page 25)
Enabled
Enabled
If you need to override any of the settings, continue with steps 5 - 8.
Otherwise, hang up. The flashing LED indicator will become solid
GREEN. Phone number setup is complete.
Continued...
PHONECELL SX3i AMPS
9
USER MANUAL 12/08/99
NAM/Phone Number Setup – Override Commands
NOTE: The following NAM Parameters are automatically set by the SID value in
step 4 on the previous page. These steps 5 - 7 are only needed if you want to
override the standard AMPS settings listed on the previous page. Otherwise,
continue to Step 4 – Optional Battery Installation on pages 12,13.
Step #5a - How to Override the Initial Dedicated Control Channel and First
Paging Channel.
If you have an “A” cellular service provider with an odd SID
(System Identifier), enter the following 2-part key sequence.
Otherwise, continue to Step #5b.
1) First press:
#
#
* 24 * _ _ _ _ #
F
2) Next press:
* 4 * _ _ _ _ #
F
(Note: enter the same 1- to 4-digit channel in both steps above.)
The spaces represent your 1- to 4-digit Initial Dedicated Control
Channel and First Paging Channel. When you turn on your Phonecell,
these channels help the service provider find you and vice-versa.
NOTE: The default setting is channel 333 for "A" service providers. To
change the setting, you must enter a 1- to 4-digit number in the range
of 0 to 1023. (For example, to set up channel 565, enter #*24*565#.) If
you enter the channel incorrectly, you'll hear three short tones followed
by the programming tone; if correct, you'll hear the programming tone
again.
Step #5b - If you have a “B” cellular service provider with an even SID
(System Identifier), enter the following 2-part key sequence.
1) First press:
#
#
* 25 * _ _ _ _ #
* 4 * _ _ _ _ #
F
F
2) Next press:
(Note: enter the same 1- to 4-digit channel in both steps above.)
The spaces represent your 1- to 4-digit Initial Dedicated Control
Channel and First Paging Channel. When you turn on your Phonecell,
these channels help the service provider find you and vice-versa.
NOTE: the default setting is channel 334 for "B" service providers. To
change the setting, you must enter a 1- to 4-digit number in the range
of 0 to 1023. (For example, to set up channel 566, enter #*25*566#.) If
you enter the channel incorrectly, you'll hear three short tones followed
by the programming tone; if correct, you'll hear the programming tone
again.
Continued...
PHONECELL SX3i AMPS
10
USER MANUAL 12/08/99
NAM/Phone Number Setup – Override Commands
Step #6 - How to Override the Number of Dedicated Control Channels.
# * 26 * _ _ #
Press:
F
The spaces represent your 2-digit range of Dedicated Control
Channels. When you first turn on the Phonecell, it automatically scans
up to 21 control channels looking for your cellular provider. Then, it
locks onto the strongest signal. NOTE: the factory default setting is 21
channels. To change the number of channels, you must enter a 2-digit
value in the range of 01 to 21. (For instance, to set up 9 control chan-
nels, enter: #*26*09#.) If you enter the range incorrectly, you'll hear
three short tones followed by the programming tone; if correct, you'll
hear the programming tone again.
Step #7 - How to Override the System Preference.
Press:
# * 7 * _ #
F
The space represents your 1-digit system preference.
enter:
enter:
enter:
enter:
0 for System “A” preferred
F
1 for System “B” preferred
F 2 for System “A” only
F
3 for System “B” only.
F
This sets the preference for your cellular provider. If you enter the pref-
erence incorrectly, you’ll hear three short tones followed by the pro-
gramming tone; if correct, you’ll hear the programming tone again.
Step #8 - Hang up. The flashing LED indicator will become solid GREEN.
Phone number setup is complete.
Optional A-Key (Authentication Code) Programming
Depending upon your cellular service provider, you may be required to enter an
Authentication Code (A-Key) before you make or receive any calls. Contact your
service provider to determine whether A-Key is required.
The A-Key is a cellular system solution to prevent cloning, counterfeiting and cel-
lular fraud. It’s a unique, 6- to 26-digit code provided by your service provider that
validates your MIN (Mobile Identification Number) and ESN (Electronic Serial
Number) before you make or receive calls. Once you’ve entered the A-Key, your
Phonecell automatically verifies the code with the cellular provider before every
call. There’s no need to re-program the unit, unless you switch to a new service
provider or change your MIN.
Use the following key sequence to program the A-Key:
Press:
#
* 27 * <A-Key> #
F
The < > brackets represent your 6- to 26-digit A-Key (Authentication
code), which is supplied by your cellular service provider.
IMPORTANT!
For security reasons, your complete A-Key is never transmitted
over the phone. However, you should keep the number in a
safe place to prevent counterfeiting, fraud or cloning.
!
PHONECELL SX3i AMPS
11
USER MANUAL 12/08/99
Step 4. Optional Battery Installation
Your Phonecell SX3i has an internal power supply with battery backup that pro-
vides uninterrupted talk time and standby operation in the event of AC power
failure. The power supply will trickle-charge the batteries while AC power is
available. However, no recharging occurs during conversation mode.
The FWT uses two 6-Volt (4.5 Amp. Hr.) batteries (not supplied). Batteries are not
shipped in the unit to prevent damage and to avoid power draining. To install bat-
teries, turn the Phonecell upside down and follow the instructions below:
DANGER!
Follow these instructions exactly. If the wire leads are not connected
to the proper terminals, the circuit board and/or transceiver may be
damaged. Always observe proper polarity (make sure the colored
wires match) while installing the wire leads and connecting wire.
!
1) Make sure that the switch is in the off
position.
2) Disconnect AC and/or DC power cord(s).
3) Locate the battery compartment, which is
next to the silver transceiver on the back
of the FWT -- see Figure. 7.
NOTE: Make sure that the power switch is
in the OFF position.
Fig. 7
4) Remove the battery compartment cover by
Battery
Compartment
pressing the securing tab downward while
sliding the lid toward the securing tab.
Power
Switch
5) Position the Phonecell so that the battery
compartment is closest to you and the sil-
ver transceiver is furthest away from you.
CAUTION!
Do Not allow the battery terminals to touch the silver transceiver
at any time, under any circumstances.
!
Batteries
6) Place an insulator (i.e. paper or
plastic) between the batteries and
silver transceiver -- as shown in
Figure 8. This will prevent the
batteries from damaging the
Phonecell’s transceiver.
Fig. 8
Continued...
Transceiver
Battery
Compartment
PHONECELL SX3i AMPS
12
USER MANUAL 12/08/99
Battery Installation – Continued
7) Connect the batteries as follows:
· Connect one end of the BLUE wire
(attached to the battery cover) to the
BLACK (-) terminal of the second
battery
RED
BLACK
BLUE
Fig. 9
· Attach the other end of the BLUE
wire to the RED (+) terminal of the
first battery – as shown in Fig. 9
· Connect the BLACK wire to the
unattached BLACK (-) terminal
of the first battery
· Attach the RED wire to the unat-
tached RED (+) terminal
of the second battery.
Fig. 10
8) Carefully lower the batteries into the
compartment as a pair, ensuring that
the wires are not pinched against the
compartment wall
or guides.
9) Once the batteries lay flat,
replace the battery compartment cover
and slide the cover closed until the
securing tab pops up. Battery
Installation is complete.
LED
Indicator
Power
Switch
DC Port
10) Re-connect the AC line cord from the
power port on the front of your
Phonecell SX3i to the power source –
see Figure 10.
AC Port
OR if an external DC power source is
used, re-connect the optional DC input
cable to the DC Input port.
11) Turn ON the Power switch. After
approximately 10 seconds, the LED
indicator on the front of the Phonecell
should turn RED, then GREEN.
NOTE: the FWT must be connected to AC
power for at least 24 hours to fully
charge the batteries before they’ll
back up your Phonecell SX3i.
l
l
AC Power
PHONECELL SX3i AMPS
13
USER MANUAL 12/08/99
Step 5. Install Your Phonecell
After you’ve selected a location and made all the necessary connections,
your Phonecell SX3 is ready for wall-mounting or desktop installation.
PRE-INSTALLATION TIPS:
· Make sure the location is dry, away from
overhead water pipes, and protected
from weather conditions.
Fig. 11
· The area should be free of airborne
contaminants.
· The Phonecell should be located within
2 meters (6 feet) of an AC power outlet.
5a. Wall-Mount Installation
Fig. 12
1) Hold the mounting template against
the wall and mark two holes for the
mounting screws–see Figure 11.
2) Drill two holes for the mounting
screws–see Figure 12.
3) Install the mounting screws into the
Fig. 13
wall, leaving about 1/8-inch (3 mm)
gap between the screw heads and
the wall–see Figure 13.
4) Locate the two mounting holes on
the back of the Phonecell – see
Figure 14.
5) Align the mounting holes on the
Phonecell with the two wall-mounted
screws. Then, mount the Phonecell
onto the screws and slide it down-
ward until the screw heads lock into
the mounting holes and the unit is
secure–see Figure 15.
Mounting
Holes
Fig. 14
Fig. 15
PHONECELL SX3i AMPS
14
USER MANUAL 12/08/99
Phonecell Installation – Continued
5b. Desktop/Tabletop Installation
After all connections are made, turn your
Phonecell SX3 face-down and attach the 3
rubber feet to the bottom–see Figure 16. Your
Phonecell SX3 is now ready for use on a
desktop, tabletop or other flat surface*.
*NOTE: Do not attach the rubber feet if the
unit is to be wall-mounted.
Fig. 16
IMPORTANT!
Your Phonecell SX3 must be placed or mounted on a flat,
level surface to allow proper ventilation. Do not block the air
vents or the space beneath your Phonecell as this could
cause the unit to overheat and fail.
!
PHONECELL SX3i AMPS
15
USER MANUAL 12/08/99
Phonecell Operation
Once your Phonecell SX3 is installed and tested, it’s ready for operation.
How to Use the LED Status Indicator
1) Plug in the AC power supply.
2) Wait approximately 10 seconds for the unit
to initialize.
3) Then, the LED indicator on the front of your
Phonecell will turn ON. The LEDStatus Table
below describes the modes and operation of
LED Indicator
this 3-color indicator.
LED Status Table
LED Color
LED Activity
Description
RED
RED
Flashing
Malfunction. Hardware fault detected.
No cellular service.
Moderate cellular signal strength.
Best cellular signal strength.
Diagnostic/programming mode.
No Power.
Continuous
Continuous
Continuous
YELLOW
GREEN
RED/GREEN Alternating
OFF None
How to Place a Call
1) Pick up your telephone handset (your phone is now “off-hook”).
2) Listen for dial tone (If service is not available, a No-Service tone is
produced. Hang-up the phone and try again.)
3) Dial the phone number.
How to Receive a Call
· When your telephone rings, pick up the handset and begin talking.
How to End a Call
· Hang-up the phone (place the handset back onto the telephone cradle).
The Hookflash Function
When you initiate the Hookflash function, it automatically lets you:
· Speed up the connection after you dial a phone number.
· Answer an incoming call that occurs when you’re dialing a phone number.
· Use special (supplementary) cellular services which may be available
in your cellular service area (see Special Cellular Services on page 18).
How to Use the Hookflash Function
Depending upon your phone, there are two ways to initiate the Hookflash function:
· Press the dedicated “HOOKFLASH” or “FLASH” key on your telephone.
· Press the hang-up or switch-hook mechanism on your phone once quickly
(approximately 1/2-second).
PHONECELL SX3i AMPS
16
USER MANUAL 12/08/99
Phonecell Operation – Continued
Important Tones and Alerts
No-Service Tone – When cellular service is not available, the receiver emits a
No-Service (fast-beeping) tone instead of the normal (steady) dial tone.
ROH (Receiver Off-Hook) Tone – If the telephone equipment remains off-hook
(off its cradle) with no dialing activity for 45 seconds, the receiver emits an ROH
tone for 60 seconds.
Incoming Call Alert – If you’re dialing a number and an incoming call occurs,
the receiver will emit an audible ring. To answer the incoming call:
· Press the “HOOKFLASH” button once. This will connect the incoming call.
· OR hang-up immediately. This will cause the phone to start ringing.
How to Adjust the Volume Level
If the volume level on your phone is too high or too low, you can adjust the levels
using the keypad on your telephone. Note: your telephone must be in Tone-
Dial (DTMF) mode to adjust the levels.
To Increase Audio Level - Increase the audio level in steps by pressing:
#
8
(also known as #
Up)
*
*
F
Continue to press #
8 until the desired level is reached.
*
To Decrease Audio Level - Decrease the audio level in steps by pressing:
(also known as # Down)
#
3
*
*
F
Continue to press #
3 until the desired level is reached.
*
NOTE: The default setting lets you adjust the audio up to three (3) steps in
either direction (Up or Down).
Fax/Data Transmission
Automatic Level Setting (ALS)
When your Phonecell SX3 detects a fax or
modem call, it automatically adjusts the Transmit
and Receive audio levels for optimum data
transmission. After the fax/data transmission is
completed, the Phonecell resets the audio levels
to their previous settings (patent pending).
Fax/Modem Compatibility
Your Phonecell is compatible with all Group 3 facsimile
machines and computer modems. Depending upon
the type of modem used and the cellular network’s
capability, data transmission rates of 2400 baud and
higher are normally possible.
PHONECELL SX3i AMPS
17
USER MANUAL 12/08/99
Phonecell Operation – Continued
Variable Dial Time (Auto SEND Delay) Option
When you place a call, your Phonecell SX3 automatically sends the phone num-
ber over the cellular network after you dial the last digit – just like a landline
phone. However, to make sure you have enough time to dial the last digit, a 3-
second Auto SEND Delay is programmed into the unit. This delay also affects
Special Functions such as Call Forwarding (see Special Cellular Services below).
You can set the Auto SEND Delay from 2 to 20 seconds using an ordinary tone-
dial (DTMF) phone, which is sometimes referred to as a POTS (Plain Old
Telephone Service) phone. Note: you cannot change the delay while you are mak-
ing a call.
How To Adjust the Auto SEND Delay - Pick up the telephone handset and
listen for dial tone. Then, enter the User-Programming mode by pressing:
* * 1 2 3 4 5 6 7 8 #
#
0
F
The dial tone should change to a steady “Programming” tone and the LED
indicator on the front of your Phonecell should blink alternately RED and
GREEN to indicate that you’re now in the Programming mode.
Next, press:
#
* 11 * <Auto SEND Delay> #
F
The < > brackets represent the Auto SEND Delay. You must enter a value
between 2 and 20 seconds. (For instance, to enter a 5-second delay, press:
# * 11* 5 #.)
If you enter the delay incorrectly, you’ll hear three short beeps followed by the
programming tone. That is your cue to re-try the steps above. If correct, you’ll
hear the programming tone again. Hang up. Your Phonecell is ready for use.
Special Cellular Services
Your Phonecell SX3 is compatible with a variety of special services such as call
forwarding, call waiting, and more. Depending upon your cellular provider, these
services may be available on a subscription basis. However, certain dialing
sequences must be entered, which vary among service providers. Please consult
your service provider for the dialing instructions for your system.
Call Forwarding – After you hear a dial tone on your telephone handset, dial the
code required by the service provider, wait for a minimum of 3 seconds or press
the HOOKFLASH.* Your Phonecell automatically transmits the call-forwarding
information. Listen for the cellular carrier response. Then, hang up the phone. If
you don’t wait for the response, your forwarding request may not be fulfilled.
*You can set this delay for 2 to 20 seconds. See the Variable Dial Time section
above. NOTE: please wait 1 second longer than the delay programmed (i.e. for
the 3-second delay mentioned above, wait 4 seconds).
Call Waiting – If your cellular provider requires codes to be entered involving dig-
its 1-9, *, and # to answer a waiting call, the Out-of-Band Signaling option must be
enabled. See the Data After SEND option on page 19.
PHONECELL SX3i AMPS
18
USER MANUAL 12/08/99
Phonecell Operation – Continued
Three-Way Conference Calls - For three-way conference calls, the Out-of-Band
Signaling option must be enabled. Pressing the HOOKFLASH function transmits
the SEND command. Please see the Data After SEND option below.
Voice Mail – Out-of-Band Signaling may need to be disabled to interact with
remote voice mail systems to prevent double-pulsing. See the Data After SEND
option below.
Authentication (A-Key) – Depending upon your cellular provider, you may be
required to enter an Authentication Code (A-Key) before you make or receive any
calls. A-Key is a cellular system solution to prevent cloning, counterfeiting and cel-
lular fraud. To program the A-Key function, see the Technician Programming
Section – page 27.
Data After SEND (In-Call Signaling) Option
Depending upon your cellular provider, the Data After SEND option may need to
be Enabled or Disabled to use special cellular features such as call waiting, three-
way conference calls, voice mail, etc. Please consult your service provider for the
required Data After Send/In-Call DTMF Signaling configuration.
The Data After SEND option is disabled (Out-of-Band signaling) at the factory. To
change the Data After SEND setting, follow the steps below.
How To Set the In-Call DTMF Signaling Option - Pick up the handset and
listen for dial tone. Then, enter the User-Programming mode by pressing:
* * 1 2 3 4 5 6 7 8 #
#
0
F
The dial tone should change to a steady “Programming” tone and the LED
indicator on the front of your Phonecell should blink alternately RED and
GREEN to indicate that you’re now in the Programming mode.
Next, press:
#
* 10 * <in-call DTMF option> #
F
The < > brackets represents the in-call DTMF signaling option. You must
enter a value between 0 and 3:
enter
F 0 for In-Band Signaling;
enter F 1 for Out-of-Band Signaling;
enter F 2 for both In-Band and Out-of-Band signaling;
enter F 3 for neither.
If you enter the option incorrectly, you’ll hear three short beeps followed by
the programming tone. That’s your cue to re-try the steps above. If correct,
you’ll hear the programming tone again. Hang up. Your Phonecell is ready
for use.
Zero Dial Delay for Frequently Called Numbers
A new patented feature enables the Phonecell to recognize your frequently called
phone numbers and send them immediately–without the 3-second Auto SEND
Delay. The Phonecell stores a list of up to 50 numbers in its memory. This list con-
tains any number that you’ve called at least twice successfully. NOTE: cycling
(turning ON/OFF) the power will erase the current list. A new list will be started
when power is re-applied. To enable or disable this feature, see page 26.
PHONECELL SX3i AMPS
19
USER MANUAL 12/08/99
Phonecell SX3 Troubleshooting
Telephone Service is Not Working
If the telephone service is not working, first check the operation of the telephone
equipment and wiring connected to your Phonecell SX3. Test the equipment on a
different service or piece of equipment to ensure proper operation, or connect a
known good telephone device to the RJ-11 port on the Phonecell SX3 unit. This
will verify the condition of the telephone equipment and the internal wiring of the
telephone service to ensure that it’s working properly. If the telephone system or
wiring is not working properly, replace or repair the equipment as required.
Otherwise, contact your cellular provider or your authorized Telular distributor.
Unable to Receive Incoming Calls
If more than one telephone or telephone device is connected to your Phonecell,
make sure that all devices are “on-hook” (hung up). If one extension is “off-hook”
(off its cradle), none of the extensions on your phone line will ring when an incom-
ing call occurs.
Moisture or Ventilation Problems
Visually inspect your Phonecell unit’s enclosure. Moisture can damage the equip-
ment. Ventilation is also very important. If there are moisture or ventilation
problems, move your Phonecell SX3 to correct as necessary.
No Power
The LED lamp on the front of your Phonecell SX3 indicates the unit’s power con-
dition. If the LED is RED, YELLOW or GREEN, your Phonecell is receiving power.
If the power cord is connected and the LED lamp is not lit, the Phonecell is not
receiving power. Verify that the AC power source and its corresponding circuit
breaker are functioning properly.
Battery Backup Failure
If you’ve installed batteries, the FWT must be connected to AC power for at least
24 hours to fully charge the batteries before they’ll back up your Phonecell SX3.
Verify that the batteries have been charged for at least 24 hours and that the
power source and its corresponding circuit breaker are functioning properly. Then,
examine the batteries for wear and corrosion. Replace the batteries if necessary.
WARNING!
Only Authorized Service Personnel should remove the cover of your
Phonecell SX3. For further assistance, contact your Authorized Telular
Representative. Please have your unit’s model and serial number ready.
!
PHONECELL SX3i AMPS
20
USER MANUAL 12/08/99
Safety Information
IMPORTANT!
To ensure safe and efficient operation, please read the following information
and observe these guidelines whenever using your Phonecell SX3 FWT.
!
Your Phonecell SX3 FWT (Fixed Wireless Terminal) functions as
both a radio transmitter and receiver. When it is ON, the FWT
receives and sends out radio frequency (RF) energy. The unit may
operate in frequency ranges between 824 MHz and 894 MHz. The
FWT employs commonly used frequency modulation (FM) tech-
niques. When you use your Phonecell SX3, the cellular system
handling your call controls the power level at which your unit trans-
mits. The power level can range from 0.006-watt to 3 watts.
Exposure to RF (Radio Frequency) Energy
In 1991, the Institute of Electrical and Electronics Engineers (IEEE), and in 1992,
the American National Standards Institute (ANSI), updated the 1982 ANSI
Standard for safety levels with respect to human exposure to RF energy. After
reviewing the available body of research, more than 120 scientists, engineers and
physicians from universities, government health agencies and industry developed
this updated Standard. In March, 1993, the U.S. Federal Communications
Commission (FCC) proposed the adoption of this updated Standard.
The design of your Telular Phonecell SX3 FWT complies with this updated
Standard. Of course, if you want to limit RF exposure even further than the updat-
ed ANSI Standard, you may choose to control the duration of your calls and oper-
ate your phone in the most power-efficient manner.
Safe Operation Requirement
Do not operate your Phonecell SX when any person is within 16 inches (40 cm) of
the antenna.
Antenna Care and Replacement
Do not use the FWT with a damaged antenna. If a damaged antenna
comes into contact with the skin, a minor burn may result. Have your
antenna replaced by a qualified technician immediately. Use only a
manufacturer-approved antenna. Unauthorized antennas, modifica-
tions, or attachments could damage the FWT and will void the Grant
of Type Acceptance.
WARNING!
Your Phonecell SX3 must be placed or mounted on a flat, level surface to
allow proper ventilation. Do not block the air vents or the space beneath
your Phonecell as this could cause the unit to overheat and fail.
!
PHONECELL SX3i AMPS
21
USER MANUAL 12/08/99
Safety Information – Continued
Batteries
All batteries can cause property damage, injury, or burns if a conductive material,
such as jewelry, keys, or beaded chains, touches exposed terminals. The material
may complete an electrical circuit (short circuit) and become quite HOT. The
Phonecell SX3 may come equipped with two batteries that serve as a backup
power supply if the AC or DC power level drops below an operable level. To install
these batteries, please refer to the Battery Installation section of this manual and
follow the instructions. If the batteries inside your unit need to be replaced for any
reason, carefully remove the batteries and replace with a set of new batteries.
Dispose of damaged or used batteries in accordance with local laws.
Driving
Check the laws and regulations on the use of cellular products
in the areas where you drive. Some jurisdictions prohibit your
using a cellular device while driving a vehicle. Even if your
jurisdiction does not have such a law, we strongly suggest that,
for safety reasons, the driver use extreme caution when operating the cellular
device while the vehicle is in motion. Always obey the law.
Electronic Devices
Most modern electronic equipment is shielded from RF energy. However, RF
energy from cellular devices may affect inadequately shielded electronic equip-
ment.
RF energy may affect improperly installed or inadequately shielded electronic
operating and entertainment systems in motor vehicles. Check with the manufac-
turer or its representative to determine if these systems are adequately shielded
from external RF energy. You should also check with the manufacturer of any
equipment that has been added to your vehicle.
Consult the manufacturer of any personal medical devices (such as pacemakers,
hearing aids, etc.) to determine if they are adequately shielded from external RF
energy.
Turn your Phonecell SX3 FWT OFF in health care facilities when any regulations
posted in the areas instruct you to do so. Hospitals or health care facilities may be
using equipment that could be sensitive to external RF energy.
Aircraft
Turn OFF your Phonecell SX3 before boarding any aircraft.
· Use it on the ground only with crew permission.
· Do not use it in the air.
To prevent possible interference with aircraft systems, U.S. Federal Aviation
Administration (FAA) regulations require you to have permission from a crew
member to use your cellular phone (or any other cellular product) while the plane
is on the ground. To prevent interference with aircraft systems, FCC regulations
prohibit using your cellular phone system while the plane is in the air.
Children
Do not allow children to play with your Phonecell to prevent damage to the unit.
PHONECELL SX3i AMPS
22
USER MANUAL 12/08/99
Safety Information – Continued
Blasting Areas
Construction crews often use remote control RF devices to set
off explosives. Therefore, to avoid interfering with blasting oper-
ations, turn your Phonecell SX3 OFF when in a "blasting area"
or in areas posted: "Turn off two-way radio."
Potentially Explosive Atmospheres
Turn your Phonecell SX3 OFF when in any area with a potentially
explosive atmosphere. It is rare, but your Phonecell SX3 or its
accessories could generate sparks. Sparks in such areas could
cause an explosion or fire resulting in bodily injury or even death.
Areas with a potentially explosive atmosphere are often, but not always, clearly
marked. They include fueling areas such as gas stations; below deck on boats; fuel
or chemical transfer or storage facilities; areas where the air contains chemicals or
particles, such as grain, dust, or metal powders; and any other area where you
would normally be advised to turn off your vehicle engine.
Do not transport or store flammable gas, liquid or explosives in the area of your
Phonecell SX3 or accessories.
Vehicles using liquefied petroleum gas (such as propane or butane) must comply
with the National Fire Protection Standard (FPA-58). For a copy of this standard,
contact the National Fire Protection Association, One Batterymarch Park, Quincy,
MA 02269, Attn: Publications Sales Division.
FCC Part 15 Class B Compliance
This Phonecell SX3 model has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and ON,
the user is encouraged to try to correct the interference by one or more of the following
measures:
· Reorient or relocate the antenna.
· Increase the separation between the equipment and the terminal.
· Connect the equipment into an outlet on a circuit different from that to which the
terminal is connected.
· Consult your Authorized Telular Distributor or an experienced radio/TV techni-
cian for help.
PHONECELL SX3i AMPS
23
USER MANUAL 12/08/99
AMPS Technician Programming
IMPORTANT!
The following commands may be used by a trained service technician to change the
configuration of the Phonecell SX3i. WARNING: these commands are intended for
use by trained service technicians only. Untrained users could damage the Phonecell,
violate local regulations and breach the service agreement with the cellular provider.
For further assistance, please contact your Authorized Telular Representative.
!
AMPS Technician Programming Commands
The Phonecell SX3 can be programmed on location with an ordinary telephone,
which is sometimes referred to as a POTS (Plain Old Telephone Set) phone.
NOTE: the Technician Programming mode is not accessible while in a call.
In the following sections, an <entered value> is comprised of the digits 0 through
9. The digits '*' and '#' are considered invalid when used inside an <entered
value>, and will cause that command/value to be rejected.
When you enter the programming mode, a timer is started. If there are no key
entries within any 2-minute period, the FWT will revert to its normal mode. Going
on-hook (hanging up the phone) will exit the programming mode.
How to Enter the Technician Programming Mode
Use the following access code to enter the Programming mode:
# * 0 * 1 2 3 4 4 3 2 1 #
Press:
F
The access code is 8 digits. If the access code is not 8 digits or does
not match the stored access code, the Technician Programming mode
cannot be not entered. This code is pre-programmed during production
and cannot be changed in the field.
If you enter the access code correctly, the dial tone should change to a
different, steady “Programming” tone and the LED indicator on the front
of the Phonecell will blink alternately RED and GREEN to indicate that
you’re in the programming mode.
PHONECELL SX3i AMPS
24
USER MANUAL 12/08/99
Technician Programming Commands – Continued
How to Set the Access Overload Class (ACCOLC)
Use the following key sequence to set the ACCOLC:
* 2 * < ACCOLC > #
Press:
#
F
The < > brackets represent the 2-digit ACCOLC. You must enter a
2-digit value between 00 and 15, otherwise the FWT will not update
or store this value; the existing stored parameter will remain. (For
example, to program the FWT for ACCOLC 8, enter: # * 2 * 08 #.)
How to Set the Access Method (EX) Option
Use the following key sequence to set the EX option:
* 3 * <EX option> #
Press:
#
F
The < > brackets represent the 1-digit EX option:
enter: F 1 if the FWT must always send the full MIN (Mobile
Identification Number) when accessing the system
enter: F 0 if not.
You must enter either 0 or 1, otherwise the FWT will not update or
store this value; the existing stored parameter will remain. The factory
default setting is 1.
How to Set the Roam Option
Use the following key sequence to set the Roam option:
* 6 * <Roam option> #
Press:
#
F
The < > brackets represent the 1-digit Roam option:
enter: F 0 to enable roaming
enter: F 1 to disable roaming.
You must enter either 0 or 1, otherwise the FWT will not update or
store this value; the existing stored parameter will remain. The factory
default setting is 0.
How to Set the Dial Tone After Remote On-Hook Option
Use the following key sequence to set the Dial Tone After Remote
On-Hook option:
* 8 * <Dial Tone option> #
Press:
#
F
The < > brackets represent the 1-digit dial tone option:
enter: F 0 for no dial tone after a remote on-hook
enter: F 1 to enable dial tone after remote on-hook.
You must enter either 0 or 1, otherwise the FWT will not update or
store this value; the existing stored parameter will remain. The factory
default setting is 1.
PHONECELL SX3i AMPS
25
USER MANUAL 12/08/99
Technician Programming Commands – Continued
How to Set the Post-Receiver Off-Hook (ROH) Option
Use the following key sequence to set the post-ROH option:
* 9 * <Post-ROH option> #
Press:
#
F
The < > brackets represent the 1-digit post-ROH option:
enter: F 0 for continuous ROH tone
enter:F 1 to turn off ROH tone and periodically check for an
on-hook condition.
You must enter either 0 or 1, otherwise the FWT will not update or
store this value and the existing stored parameter will remain. The
factory default setting is 1.
How to Set the Pulse Dial Option
Use the following key sequence to set the Pulse Dial option:
* 12 * <Pulse Dial option> #
Press:
#
F
The < > brackets represent the 1-digit Pulse Dial option:
enter: 0 to disable pulse dialing capability
F
enter:F 1 to enable pulse dialing capability.
You must enter either 0 or 1, otherwise the FWT will not update or
store this value; the existing factory default setting is 1.
How to Initiate a Ring-Back Request
Use the following key sequence to initiate an immediate Ring Back:
* 13 * #
Press:
#
F
There is no Ring Back value to be entered; the command activates
when the phone is placed on-hook.
How to Restore the Factory Default Settings
Use the following key sequence to restore the factory default settings:
* 15 * #
Press:
#
F
There is no Restore Defaults value to be entered; the command acti-
vates immediately. If you enter a value, it will be invalid and the FWT
will not restore the factory defaults. Note: NAM (Phone Number Setup)
data is not affected by this command and will not be changed.
How to Enable/Disable the Zero Dial Delay Option
Use the following key sequence to set the Zero Dial Delay option:
* 21 * <Zero Dial Delay option> #
Press:
#
F
The < > brackets represent the 1-digit Zero Dial Delay option:
enter:
enter:
0 to disable Zero Dial Delay option
F
1 to enable Zero Dial Delay option
F
You must enter either 0 or 1, otherwise the FWT will not update or
store this value; the existing stored parameter will remain. The factory
default setting is 1.
PHONECELL SX3i AMPS
26
USER MANUAL 12/08/99
©1999 Telular Corporation, all rights reserved. Printed in the USA.
Part No. 56016602
|